Whirlpool ADG 9928/1 Mode d'emploi télécharger pdf

Whirlpool is a registered trademark of Whirlpool USA

5019 396 01091

Before using the dishwasher, read the

installation and maintenance instructions carefully!

ADG 9928

1) Programme data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g.

different loads, options, different sensor settings (only with sensor programmes), different water supply temperatures, as well

as water hardness and power supply voltage.

2) Reference programme for energy label in compliance with EN 50242. - Important information for Test Laboratories:

for

detailed information on the EN/Standard loading comparison test and other tests, contact the following address:

“nk_customer@whirlpool.com”.

1. OVERVIEW

On button

Off button

Time and failure display

With “Delayed start” selected, it indicates the time

remaining until the start of the programme (hh). Toward

the end of the programme, during the drying cycle, the

display will indicate the time remaining in minutes.

If “F..” appears on the display, see chapter 5 “What to do if ...”.

Delayed start button

The wash cycle can be programmed to start after

1- 24 hours (with each successive touch of the button,

the delayed start indicator increases by 1 hour, and after

24 returns to 00).

Then press the START button. The dishwasher will start

at the set time.

Detergent setting upon initial use and when using a different type of

detergent

1. Press and hold the programme selection button, also press the

“Delayed start” button. The selected detergent type will be shown

on the display.

2. Using the delayed start button, select the desired detergent

(“--” = powder detergent, “2 l” = 2 in 1, “3 l” = 3 in 1, “A l” = all

other combined action detergents (in this way, the rinse aid and/or

salt indicator is deactivated). The selected detergent type will be

shown on the display.

3. Wait 5 seconds or switch off the appliance, the selected detergent

type is memorised. It is shown on the display for approx. 3 seconds

after the appliance is switched on. Note that only after changing the

detergent type is it possible to select the desired programme and, if

necessary, select the delayed start button.

Programme selection button

Press the button repeatedly until the desired programme

indicator lights up.

Start button

Switches “on” when the dishwasher is operating.

Flashes when a fault occurs. Switches off at the end of

the programme.

START button RESET function:

Press this button for at least 2 seconds; the selected

programme and options are cancelled. Main failure

displays (repeated flashing of the START indicator lamp)

can be cancelled by RESETTING. Detailed instructions

are given in chapter 5 “What to do, if...”.

Rinse aid level indicator and salt level indicator

These indicator lamps light up when rinse aid or salt

need to be added.

Add just before starting a wash programme.

Running programme indicator

A LED light projected on the floor indicates that the

dishwasher is working.

Table 1.1.

Programme chart

Detergent

dispenser

Consumption

Programmes

Available

options

Loading instructions large small Litres kWh Minutes

Auto Sensor 50-65°C

Recommended programme for

routine washes, with dried-on

food (e.g. EN 50242).

X X 11-16 1.10-1.50 100-130 ±

Rapid 40°C

Lightly soiled crockery, with no

dried-on food.

X — 10.0 0.65 30 ±

Eco

50°C

Normally soiled crockery.

Energy saving programme.

X X 12.0 1.05 165 ±

Intensive 70°C

Recommended programme for

heavily soiled crockery,

especially suitable for pans and

saucepans.

X X 14.0 1.55 155 ±

Half Load 50°C

Ideal for washing a half load of

lightly or normally soiled

crockery.

X X 10.0 1.04 145 ±

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - 1. OVERVIEW

Whirlpool is a registered trademark of Whirlpool USA5019 396 01091Before using the dishwasher, read the installation and maintenance instructions care

Page 2 - 2. QUICK REFERENCE GUIDE

22. QUICK REFERENCE GUIDEDetailed instructions are given in the following pages, see also chapter “5. What to do if...”1. Switch on the applianceOpen

Page 3 - 3. HOW TO USE THE APPLIANCE

33. HOW TO USE THE APPLIANCEPROGRAMME SELECTIONPress the button or to bring up the desired programme on the display. The appliance must be switche

Page 4

43. HOW TO USE THE APPLIANCEc. How to adjust the rinse aid dosage regulatorThe rinse aid dosage can be adjusted to the detergent used. The lower the s

Page 5

53. HOW TO USE THE APPLIANCEHOW TO LOAD THE RACKSUPPER RACK - depending on the modelLong-handled utensils (kitchen knives) must be arranged with the s

Page 6

64. PRECAUTIONS AND GENERAL RECOMMENDATIONS1. PackingThe packaging materials are 100% recyclable and marked with the recycling symbol. .2. Removing t

Page 7 - 5. WHAT TO DO IF

75. WHAT TO DO IF...If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults

Page 8

85. WHAT TO DO IF...Crockery and cutlery ... Possible causes/solutions...are not perfectly clean/have food residues- In the event of frequent use of t