Whirlpool D Manuel d'utilisateur télécharger pdf (Page 2)

5019 301 10287

Whirlpool is a registered trademark of Whirlpool USA

Add detergent as indicated on the front page and as

described in the chapter “Detergent and Additives”

in your Instructions for Use.

Close the door and turn the programme selector to the

desired programme and temperature. The indication

lamp next to the

“Start/Pause”

button flashes.

Push the button(s) of any option(s) desired - the

respective indication lights up.

When the combination of programme and additional

option(s) is not possible, the indication lights switch

off automatically. Unsuitable combinations of

options are deselected automatically.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. Increases the cycle time

by approximately 15 min.

“Eco” button

•With a modified temperature profile and a slightly

prolonged washing duration, the optimum

combination of excellent washing result and even

lower energy consumption is achieved.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with

very soft water, washing baby linen and helps

people with allergies.

“Easy ironing” button

• Can be used together with “Cotton”,

“Synthetics” and “Daily load” programmes to

make ironing easier.

• Increases the water quantity and the clothes are

spun very gently.

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain

during rinse. The water is drained out only.

CONSUMPTION DATA

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton 95 5.0 49

1.90 2:00

Cotton 60 5.0 44 0.95 2:10

Cotton with “Eco”

***

60 5.0 44 0.85 2:20

Cotton 40 5.0 44 0.60 2:00

Synthetics 60 2.5 50

0.70 1:30

Synthetics 40 2.5 45 0.55 1:15

Delicates 30 1.5 50 0.50 0:45

Daily load 40 3.0 45 0.45 1:00

Quick wash 30 3.0 40 0.40 0:30

Wool 40 1.0 55 0.60 0:45

Handwash 40 1.0 45 0.60 0:40

Lingerie 30 1.0 45 0.50 0:40

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home

may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions

applicable at that time.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

The “Start Delay” allows to run the machine at the

consumer’s convenience, for example at night when

electricity is cheaper.

• Select programme, temperature and options.

• Press the “Start Delay” button to select the delay

time by 1, 3, 6, 9 or 12 hours.

•Press the

“Start/Pause”

button.

The indication next to the “Start Delay” button

lights up and goes off when the programme starts.

• Once having pressed the

“Start/Pause”

button,

the countdown of the time delay begins. When

the programme starts, the start delay indicator

light goes off and is replaced by the programme

sequence indication.

• After the

“Start/Pause”

button has been pressed,

the number of hours preselected can be reduced

by pressing again the “Start Delay” button.

To cancel the “Start Delay”

..before you press the “Start/Pause” button:

• Turn the programme selector to another

position or press the

“Reset”

button.

..after having pressed the “Start/Pause” button:

• Press the “Reset” button for at least 3 seconds -

the start delay indicator light goes out.

Open the tap and press the

“Start/Pause”

button.

The indication lamp next to the

“Start/Pause”

button lights up. The programme sequence indicator

shows the current programme phase, running from

left to right through Wash, Rinse, Spin/Drain.

When the programme phase is finished, the

corresponding indication goes out.

Before starting and after end of a programme, the

lamp lights to show that the door can be opened. As

long as a wash programme is running, the door

remains locked and must on no account be forced

open. In case you have an urgent need to open it

during a running programme, refer to “Cancel

(Reset) a running programme before the end”.

“Service”

Lighting up of the “Service” indication can be caused by

a fault in an electrical component. Refer to the

“Troubleshooting Guide” in your Instructions for Use; if

the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply.

Open the water tap; if the indication still lights up,

refer to the “Troubleshooting Guide” in the

Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the

drain hose is kinked or the filter must be cleaned; in

the latter case refer to the Instructions for Use

(“Removing the Filter”).

• All the lights of the programme sequence

indicator are off, and the “Door open”

indication lights up.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

1. Press the

“Start/Pause”

button to pause the

programme. The light flashes.

2. Select the new programme (with temperature),

any options and another spin speed if you want.

3. Press the

“Start/Pause”

button again. The new

programme continues at the same position

where the previous programme was interrupted.

Do not add detergent for this programme.

The

“Reset”

button cancels a programme before

the end.

•Press the

“Reset”

button for at least 3

seconds. Any existing water is drained out

before the door can be opened.

START DELAY

PROGRAMME START

“DOOR OPEN” INDICATION

RED INDICATIONS

PROGRAMME END

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

1 2

5019 301 10287 1

Commentaires sur ces manuels

Pas de commentaire

Whirlpool D Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Non Whirlpool D