ELECTRICAL CONNECTION
WARNING
This operation must be performed by a qualied technician.
WARNING
The electrical connections must
comply with local regulations.
• The earthing of this applian-
ce is compulsory by law.
• Do not use an extension
cord.
L
Earth
(yellow/green)
N
IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.
ASSEMBLY
After having cleaned the perimeter surface,
apply the supplied gasket to the hob as shown in
the gure
Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.
NOTE: the power supply cable must be long enough to permit its upward extraction.
To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and
fasten them by means of their screws in accordance with the thickness of the worktop (see the following gures).
Top 20 mm
Top 30-50 mm
ADJUSTMENT TO DIFFERENT TYPES OF GAS
WARNING
This operation must be performed by a qualied technician.
If the appliance is intended to operate with a dierent gas from the gas type stated on the rating plate and information
label on the top of the hob, change the injectors.
Remove the information label and keep it with the instructions booklet.
Use pressure regulators suitable for the gas pressure indicated in the Instruction.
• The gas nozzles must be changed by After Sales Service or a qualied technician.
• Nozzles not supplied with the appliance must be ordered from After Sales Service.
• Adjust the minimum setting of the taps.
NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it
will go.
IMPORTANT: should you experience diculty in turning the burners knobs, please contact the After Sales Service
for the replacement of the burner tap if found to be faulty.
REPLACING THE INJECTORS see the injector table in the Instruction
• Remove grids (A).
• Extract burners (B).
• Using a socket spanner of the appropriate size unscrew
the injector (C), unscrew the injector to be replaced.
• Replace it with the injector suitable for the new type of
gas.
• Re-assemble the injector in (D).
• If you have a multiple crown burner use side spanner to
replace the injector (E).
Before installing the hob, remember to ax the gas calibra-
tion plate supplied with the injectors in such a way that it
covers the existing information relating to gas calibration.
ADJUSTING MINIMUM GAS SETTING OF TAPS
To ensure that the minimum setting is correctly adjusted,
remove the knob and proceed as follows:
• tighten screw to reduce the ame height (-);
• loosen screw to increase the ame height (+).
The adjustment must be performed with the tap in minimum
gas setting position (small ame)
.
• The primary air of the burners does not need to be adju-
sted.
• At this stage, light up the burners and turn the knobs
from max position
to minimum position to check
ame stability.
Upon completion of adjustment, reseal using sealing wax or
an equivalent material.
REFERENCE TO LOCAL REGULATIONS
Installation must be performed in accordance with standard
NBN D 51-003.
AFTERSALES SERVICE
Before calling the After-Sales Service, make sure you can give
the following information:
- type of fault or problem;
- exact model (written on the label axed to the in-
struction/warranty);
- service number that follows the word SERVICE on the
rating plate under the hob and on the label axed to
instruction/warranty;
- your complete address and phone number.
If any repairs are required, please contact an authorised
After-Sales Service, as indicated in the warranty.
(12 pages)
(56 pages)
(44 pages)
(64 pages)
(76 pages)
(76 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels