Whirlpool T TNF 8211 OX Guide d'utilisation et d'entretien Page 5

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 26
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 4
EN
5
Appliances could have special
compartments (Fresh Food
Compartment, Zero Degree
Box,...). In case not dierently
specied in the specic booklet
of product, they can be
removed, maintaining
equivalent performances.
C-Pentane is used as blowing
agent in the insulation foam and
it is a ammable gas.
INSTALLATION
The appliance must be handled
and installed by two or more
persons. Use protective gloves
to unpack and install the
appliance.
Installation and repairs must be
carried out by a qualied
technician, in compliance with
the manufacturers instructions
and local safety regulations. Do
not repair or replace any part of
the appliance unless specically
stated in the user manual.
Children should not perform
installation operations. Keep
children away during
installation. Keep the packaging
materials (plastic bags,
polystyrene parts, etc.) out of
reach of children, during and
after the installation.
Be careful not to damage the
oors (e.g. parquet) when
moving the appliance. Install the
appliance on a oor or support
strong enough to take its weight
and in a place suitable for its size
and use.
After unpacking the appliance,
make sure that it has not been
damaged during transport. In
the event of problems, contact
the dealer or your nearest After-
sales Service.
The appliance must be
disconnected from the power
supply before any installation
operation.
During installation, make sure
the appliance does not damage
the power cable.
To guarantee adequate
ventilation, leave a space on
both sides and above the
appliance. The distance
between the rear of the
appliance and the wall behind
the appliance should be 50mm,
to avoid access to hot surfaces. A
reduction of this space will
increase the Energy
consumption of product.
Reversible doors - if it is
necessary to change the
direction in which the doors
open, please contact the
Technical Assistance Centre.
Only activate the appliance
when the installation has been
completed.
Wait at least two hours before
switching the appliance on, to
ensure that the refrigerant
circuit is fully ecient.
Make sure the appliance is not
near a heat source.
ELECTRICAL WARNINGS
For installation to comply with
current safety regulations, an
omnipolar switch with minimum
contact gap of 3mm is required
and the appliance must be
earthed.
If the power cable is damaged,
replace with an identical one.
The power cable must only be
replaced by a qualied
technician in compliance with
the manufacturer instruction
and current safety regulations.
Contact an authorized service
center.
If the tted plug is not suitable
for your socket outlet, contact a
qualied technician.
The power cable must be long
enough to connect the
appliance, once tted in its
housing, to the main power
supply. Do not pull the power
supply cable.
Do not use extension leads,
multiple sockets or adapters.
Do not operate this appliance if
it has a damaged mains cord or
plug, if it is not working
properly, or if it has been
damaged or dropped. Keep the
cord away from hot surfaces.
The electrical components must
not be accessible to the user
after installation.
Do not touch the
appliancewithany wet part of
the body and do not operate it
when barefoot.
CLEANING AND
MAINTENANCE
Never use steam cleaning
equipment.
Wear protective gloves for
cleaning and maintenance.
The appliance must be
disconnected from the power
supply before any maintenance
operation.
Do not use abrasive or harsh
cleaners such as window sprays,
scouring cleansers, ammable
uids, cleaning waxes,
concentrated detergents,
bleaches or cleansers containing
petroleum products on plastic
parts, interior and door liners or
gaskets. Do not use paper
towels, scouring pads, or other
harsh cleaning tools.
Vue de la page 4
1 2 3 4 5 6 7 8 9 10 ... 25 26

Commentaires sur ces manuels

Pas de commentaire