ELECTRONIC ELECTRIC DRYERUse & Care GuideFor questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301o
101. Remove center silver-colored terminal block screw.2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire
113. Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw.4. Place the hooked ends of the other
12When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked en
13Venting RequirementsWARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.IMPORTANT: Observe all governing codes and ordinances
14Plan Vent SystemChoose your exhaust installation typeRecommended exhaust installationsTypical installations vent the dryer from the rear of the drye
15Determine vent path Select the route that will provide the straightest and most direct path outdoors. Plan the installation to use the fewest num
16Connect Inlet HoseThe dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.1. Turn cold water faucet off
1712. If you live in a hard water area, use of a water softener is recommended to control the buildup of scale through the water system in the dryer.
18To use an Automatic CycleNOTE: A light next to each feature will glow green when the feature is selected or will glow amber when the feature is sele
19NOTE: During the Enhanced Touch Up Cycle, you can change the settings for Time, Temperature, the WRINKLE SHIELD™ feature and Cycle Signal. During th
2TABLE OF CONTENTSDRYER SAFETY...2INSTALLATION INSTRUCTIONS...
20CyclesSelect the drying cycle that matches the type of load you are drying. See Automatic Preset or Manual Preset Cycle Settings chart.Cycle Control
21Air OnlyUse the Air Only setting for items that require drying without heat such as rubber, plastic and heat-sensitive fabrics. This chart shows exa
22Cycle Signal The End of Cycle Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle
234. Close the door.5. Select a timed drying cycle and temperature, or an air cycle (see following chart). Items containing foam, rubber, or plastic m
243. Wipe drum thoroughly with a damp cloth.4. Tumble a load of clean cloths or towels to dry drum.NOTE: Garments that contain unstable dyes, such as
25 TROUBLESHOOTING First try the solutions suggested here and possibly avoid the cost of a service call...Dryer OperationDryer will not run Has a hou
26Dryer ResultsClothes are not drying satisfactorily, drying times are too long, or load is too hot Is the lint screen clogged with lint? Lint screen
27ASSISTANCE OR SERVICEBefore calling for assistance or service, please check “Troubleshooting.” It may save you the cost of a service call. If you st
WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTYONE YEAR LIMITED WARRANTYFor one year from the date of purchase, when this major appliance is operated a
3INSTALLATION INSTRUCTIONSTools and PartsGather the required tools and parts before starting installation. Read and follow the instructions provided w
4 For close-clearance installations between 31.5" (80.01 cm) and 37" (93.98 cm), see “Plan Vent System” section for venting requirements.Mo
5 A level floor with a maximum slope of 1" (2.5 cm) under entire dryer. If slope is greater than 1" (2.5 cm), install Extended Dryer Feet K
6Recommended installation spacing for cabinet installation For cabinet installation, with a door, minimum ventilation openings in the top of the cabi
7Electrical RequirementsIt is your responsibility To contact a qualified electrical installer. To be sure that the electrical connection is adequate
8Electrical Connection1. Disconnect power.2. Remove the hold-down screw and terminal block cover. 3. Install strain relief.Style 1: Power supply cord
9 Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain
Commentaires sur ces manuels