Whirlpool Light programmable oven Manuel d'installation

Service & Installation manual Light programmable oven with boiler

- 10 - Exhaust The WHIRLPOOL ovens are equipped with an open/direct exhaust system that removes surplus humidity from the oven chamber. The exhaust

- 11 - Checking before Use The oven should be checked before you start using it. On the outside • Check that the oven has not been damaged in tran

- 12 - Annual Service Check Customer: Address: By: Postal code: Serial No of t

- 13 - 6. Steam generator: Functioning correctly YES NO Heating elements (check for leaks) Load distribution on phases

- 14 - Start Menu  Set temperature (press temperature key, temperature flashes, set temperature with turn switch, press temperature key again t

- 15 - Oven set-up  To enter set-up mode, press hot-air key and steaming/preheating key for 2 sec.  To leave set-up mode, turn switch to the l

- 16 - Set-up Mode U In the set-up function, it is possible to set the oven controller to match the mechanical set-up and the choice of software. I

- 17 - 0= OFF, 1= 10 programs with 3 process steps. NOTE: It is still possible to activate the cleaning program even though the program mode is not ac

- 18 - Display shows setting Activates each function briefly Display indicates whether the function is active Display shows a description of the

- 19 - Test Mode D0-D6 In the test mode, it is possible to activate all electrical components. This is very useful in connection with fault detection

- 2 - Table of Contents Page Preface and terms of warranty 3 Rating plate 4 Installation and connection 5 -Installation 6 -W

- 20 - Test Mode D7-D15 D7 Filling valve This function activates solenoid valve MV2. You activate or deactivate the function by pressing the step k

- 21 - Test Mode D16-D20 D16 Core temperature This function is not available on B models. C and K models can use only one core temperature probe, it

- 22 - Test Functions D21-28 D21 Water level Here it is possible to read the status of SE2. In the display next to ”Time”, the conductivity is show

- 23 - Test Mode D29-D47 D29 CombiWash water Only possible on ovens with CombiWash. This function activates solenoid valve MV4. You activate or deact

- 24 - Display shows setting Display shows setting Display shows "b" No. Display shows description of "b" function Display sho

- 25 - User Menu B1-B7 B1 Save presettings In this function, you save the preset time and temperature. If, for instance, the end user uses HOT AIR a

- 26 - User Menu B8-B13 B8 Exhaust In this function, you choose whether the oven should start up the extraction hood. 0= Extraction hood not cont

- 27 - User Menu B14-B21 B14 year In this function, you set the year. 1. Press the key next to the temperature display (digit flashes). 2. Turn the

- 28 - User Menu B22-B24 B22 Screen saver In this function, you set the time that should pass until the clock appears in the display. Press step ke

- 29 - Error codes All keys can be used to acknowledge an error message. Display shows error "Er" No Display shows description of error

- 3 - Preface and Terms of Warranty You are now the owner of one of the leading oven products on the market. All WHIRLPOOL products are currently su

- 30 - Error codes Error code 3: GENRA HOT Generator too hot (Generator thermoswitch has tripped. Reconnect by pressing button under oven.) Erro

- 31 - Appendix No 1 WHIRLPOOL INSTALLATION CHECKLIST FOR VISUAL COOKING OVENS To be filled out at each installation of a WHIRLPOOL oven. In ord

- 32 - Access to the oven: Recommended distance for service and for installation near other heat-generating appliances (all oven sizes). Al

- 33 - Appendix No 2 WHIRLPOOL INSTRUCTION CHECKLIST FOR VISUAL COOKING OVENS To be filled out for each installation of a WHIRLPOOL oven. In ord

- 34 - Notes: _________________________________________________________________________ ________________________________________________________

- 35 - Notes: _________________________________________________________________________ ___________________________________________________________

- 4 - Rating Plate When communicating with WHIRLPOOL, we kindly ask you inform us of the serial number of the oven that is stated on the approval p

- 5 - Installation and Connection Unpacking the oven The oven is best handled while still in its wrapping. Wherever possible, use a lifting trolley

- 6 - Installation and Connection Installing the oven To ensure that the oven functions correctly when installed, it should be placed upright and

- 7 - Installation and Connection Water connection WHIRLPOOL ovens have one or two water connections. To facilitate cleaning and service, the oven

- 8 - Installation and Connection Drain connection From the factory, the WHIRLPOOL ovens are equipped with a drain system that removes surplus wat

- 9 - Installation and Connection Electrical connection/survey of supply lines The electrical connection must be carried out by an authorised elec