Whirlpool GMR 7511/IXL Mode d'emploi télécharger pdf

5019 300 01063

LIGHTING THE BURNERS

• To ignite one of the burners, turn the relative knob anti-clockwise to the maximum flame setting .

• Press the knob against the control panel to ignite the burner.

• After the burner has ignited, keep the knob pressed for about 5 seconds to allow the thermocouple to warm up.

This safety device shuts off the gas if the flame goes out accidentally (draughts, interruption of gas, liquids boiling over,

etc.).

• The device must not be pressed for more than 15 sec. If, after that time has elapsed, the burner does not remain lit,

wait at least one minute before trying to light it again.

- The burner might go out when the knob is released. This means that the thermocouple has not warmed up enough.

In this case, repeat the operations described above.

PRATICAL ADVICE FOR USING THE BURNERS

For optimum burner performance, observe the following

rules:

- Use pots and pans that fit the burners (see table on the

right).

- Only use flat-bottomed pots and pans.

- Use the correct amount of water for cooking foods and

keep the pot covered.

1. Removable panstand grids

2. Auxiliary burner

3. Semirapid burner

4. Rapid burner

5. Semirapid burner

6. Rapid Burner

7. Auxiliary burner control knob

8. Semirapid burner control knob

9. Rapid burner control knob

10. Semirapid burner control knob

11. Rapid burner control knob

SYMBOLS

Tap closed

Maximum flame

Minimum flame

Burner Pot Ø

ultra-rapid From 24 to 26 cm

Rapid From 24 to 26 cm

semi-rapid From 16 to 22 cm

Auxiliary From 8 to 14 cm

DIMENSIONS AND DISTANCES TO BE MANTAINED (mm)

N.B: If the distance "A" between the wall cabinets is between 600 mm and 730 mm, the height "B" must be

a minimum of 530 mm. If the distance “A” between the wall cabinets is greater than the width of the

hob, the height “B” must be a minimum of 400 mm. In case of installation of a hood above the

cooktop, please refer to the hood instructions for the correct distance.

INJECTORS TABLE CATEGORY II2H3+

ELECTRIC SUPPLY: 230 V ~ 50 Hz

Type of gas used Type of burner Injector

marking

Nominal

heating

capacity kW

Rated

consumption

Reduced heat

capacity kW

Gas pressure (mbar)

min. nom. max.

NATURAL GAS

(Methane) G20

ultra-rapid

Rapid

semi-rapid

Auxiliary

136

128

3.50

3.00

1.65

1.00

333 l/h

286 l/h

157 l/h

95 l/h

0.60

0.35

0.30

17 20 25

LIQUID

PETROLEUM GAS

(Butane) G30

ultra-rapid

Rapid

semi-rapid

Auxiliary

3.50

3.00

1.65

1.00

254 g/h

218 g/h

120 g/h

73 g/h

0.60

0.35

0.30

20 28-30 35

LIQUID

PETROLEUM GAS

(Propane) G31

ultra-rapid

Rapid

semi-rapid

Auxiliary

3.50

3.00

1.65

1.00

250 g/h

214 g/h

118 g/h

71 g/h

0.60

0.35

0.30

25 37 45

Type of gas used Model

configuration

Nominal heating

capacity kW

Total nominal

consumption

Air required (m

) for burning

of gas

G20 20 mbar 5 burners 10.8 1028 l/h 9.52

G30 28-30 mbar 5 burners 10.8 785 g/h 30.94

G31 37 mbar 5 burners 10.8 771 g/h 23.80

GMR 7511 PRODUCT SHEET

To ensure best use of the hob, please read these instructions for use carefully and keep them for future reference.

1 2 3 4

Résumé du contenu

Page 1 - GMR 7511 PRODUCT SHEET

5019 300 01063LIGHTING THE BURNERS• To ignite one of the burners, turn the relative knob anti-clockwise to the maximum flame setting .• Press the kno

Page 2 - INSTALLATION

PRECAUTIONS AND GENERAL RECOMMENDATIONSTo get full satisfaction from your hob, please read these instructions carefully and keep them for future consu

Page 3

INSTALLATIONGAS CONNECTION• The gas supply system must comply with local regulations.• You can find specific local regulations for some countries in t

Page 4 - AFTER-SALES SERVICE

ADJUSTING MINIMUM GAS SETTING OF TAPSTo ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows:• tighten the sc