Whirlpool ADG 9641 Mode d'emploi télécharger pdf

Whirlpool is a registered trademark of Whirlpool USA

Before using the dishwasher, read the installation and maintenance instructions carefully!

5019 396 01196

ADG 9641

1) Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to different loads, extra

functions, different settings, water supply temperatures, water hardness and power supply voltage.

2) Programme for energy data label in conformity with EN 50242. - Information for Test Laboratories:

for detailed information on the EN/Standard

loading comparison test and other tests, contact the following address: “[email protected]”.

3) The antibacterial action has been proven in collaboration with the Pasteur Institute of Lille (France), in conformity with. Standard NF EN 13697 of

November 2001.

1. OVERVIEW

Programme selection button

Press the button (repeatedly) until the indicator lamp of the

desired programme lights up (see table 1.1).

At the end of the wash cycle, the last programme selected is

memorized.

Half Load/Multizone

Load the

upper or lower rack only

Factory setting = Wash upper and lower rack (both indicator

lamps light up)

Press once = Wash

lower rack

(the indicator lamp lights up)

Press twice = Wash

upper rack

(the indicator lamp lights up)

At the end of the programme, the most recently selected

setting remains memorised.

If the upper rack is not being washed, the “Wash lower rack”

indicator lamp should be lit.

Antibacterial rinse

This function activates an antibacterial rinse at the end of the

wash cycle, guaranteeing a further reduction of bacteria. Press

the button to activate or deactivate the function. This function

can be used with those programmes marked with the relative

symbol in table 1.1.

The dishwasher door must be kept shut for the entire duration

of the programme in order to guarantee reduction of bacteria.

If the door is opened the indicator lamp starts flashing.

At the end of the programme, the most recently selected

setting remains memorised.

Detergent setting upon initial use and when using a different

type of detergent

Indicator lamp off = Powder/gel detergent (factory setting).

If using combined detergents, press and hold the button for 3

seconds; the indicator lamp lights up = rinse aid and salt

indicators are deactivated.

From water hardness level 5, the salt indicator remains active.

At the end of the programme, the most recently selected

setting remains memorised.

Fault indication and wash time display

In normal operation it indicates the remaining time (h:min),

whereas with “Delayed start” selected it indicates the time

remaining until programme start (e. g. h 01). If using a sensor

programme, a dotted line indicates that the calibration process

is underway (lasting up to 20 minutes).

In the presence of a fault indication “F.. / E..”, refer to Section 5

“What to do if...”.

Delayed Start button

Push the button (repeatedly) to delay the start of the

programme. Adjustable from 1 to 24 hours. With each

successive touch of the button, the delayed start indicator

increases by 1 hour, and after “h 24” returns to “h 00”. Then

press the START button. The wash programme will start after

the set time.

Start/Resume button

The indicator lamp lights up during operation, flashes when the

programme is interrupted before completion and switches off at

the end of the programme.

Cancel/Off button

Press the button to switch the dishwasher off or to interrupt the

selected programme.

If the Cancel/Off indicator lamp flashes repeatedly, this indicates

a fault: see chapter 5 “What to do if...”.

Salt level indicator and rinse aid level indicator

These light up at the end of the programme if salt or rinse aid

needs topping up.

Only add just before starting a wash cycle.

Table 1.1.

Programme Table

Detergent

compartment

Consumption

Programmes

Selectable

options

Description of programme

large small Litres kWh Minutes

Sensor 40-70°C

Normally or heavily soiled crockery,

including pots and pans.

X X 7-14 0.99-1.80 70-185 ±

Pre-Rinse cold

Crockery to be washed later. — — 4.0 0.03

14 ±

Quickwash 45°C

Lightly soiled crockery, with no dried-on

food.

X — 11.0 0.80 30 ±

Eco

50°C

Normally soiled crockery. Energy-saving

programme.

X X 12.0 1.05 165 ±

Rapid daily 60°C

Normally soiled crockery. X — 10.0 1.30 80 ±

Intensive 70°C

Recommended programme for heavily

soiled crockery, especially suitable for pots

and pans.

X X 14.0 1.55 155 ±

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - 1. OVERVIEW

Whirlpool is a registered trademark of Whirlpool USABefore using the dishwasher, read the installation and maintenance instructions carefully!1GB5019

Page 2 - 2. QUICK REFERENCE GUIDE

2Change the programme in progress:- Press the Cancel/Off button.- Close the door.- (Water drains for up to 60 seconds).- Open the door.- Select a

Page 3 - 3. HOW TO USE THE APPLIANCE

33. HOW TO USE THE APPLIANCEHOW TO FILL THE DETERGENT DISPENSEROnly fill the detergent dispenser prior to starting a wash programme. Only use detergen

Page 4

43. HOW TO USE THE APPLIANCEHOW TO CHECK/FILL/ADJUST SALTOnly use regeneration salt specifically intended for dishwashers.a. How to check the salt lev

Page 5

53. HOW TO USE THE APPLIANCEHOW TO LOAD THE RACKSUPPER RACK - depending on model:Long-handled utensils (kitchen knives) must be arranged with the shar

Page 6

64. PRECAUTIONS AND GENERAL RECOMMENDATIONS1. PackagingThe packaging materials are 100% recyclable and marked with the recycling symbol .2. Removing

Page 7 - 5. WHAT TO DO IF

75. WHAT TO DO IF...If a fault occurs, before contacting the After-Sales Service, make the following checks to try and remedy the problem. Most faults

Page 8

85. WHAT TO DO IF...Crockery and cutlery ... Possible causes/solutions...are not perfectly clean/have food residues- In the event of frequent use of l