Whirlpool W10197087 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Réfrigérateurs Whirlpool W10197087. Whirlpool W10197087 Manuel d'utilisation Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 4
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
INSTRUCTION SHEET FOR BUILT-IN REFRIGERATOR
HANDLE ACCESSORY
BEFORE YOU BEGIN: The handle and handle mounting hardware must be installed before installing the custom panel. A qualified
cabinetmaker must perform the installation.
IMPORTANT: Do not use these handle(s) on acrylic panels.
TOOLS NEEDED:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
PARTS SUPPLIED:
* (#) represents quantities for French door bottom mount freezer
models.
Install the refrigerator handle
IMPORTANT: See Figure 1 and the Refrigerator Door table for
handle mounting hole requirements as well as handle mounting
hole locations.
1. Measure from the bottom of the custom panel and mark your
first hole location as shown in Figure 1 and Refrigerator Door
table.
Figure 1: Refrigerator door
NOTE: Measurements from the side edge of the door will
depend on specific application.
2. Drill a ³⁄₁₆" (4.76 mm) hole at that location, then measure up
from the bottom hole to determine the location of the second
hole. Countersink both holes on the inside of the panel, ¹⁄₄"
(6.35 mm) deep and ⁵⁄₈" (1.58 cm) diameter for screw head
clearance.
3. Install two mounting studs to the custom panel using the
screws provided. Check that the head of the screw is flush
with the panel.
4. Install handle to handle mounting studs and tighten the
setscrews. Some adjustments of the handle mounting studs
may be required to allow the handle to fit over both mounting
studs.
NOTE: For products with one refrigerator door, the setscrew
should face the hinge side of the door. For products with two
refrigerator doors, the setscrews should face the center of the
product.
5. If you have two doors, repeat steps 1-4.
Cordless drill
⁵⁄₁₆" socket driver
³⁄₃₂" Allen wrench
Drill bits
Flat-blade screwdriver
Tape measure
Pencil
Handle - freezer door
Handle - refrigerator
door (2)*
4 Studs - handle
mounting (6)*
4 Screws - #10-24 x 1"
hex washer head (6)*
Refrigerator Door
Dimension Bottom Mount
Freezer
French Door Bottom
Mount Freezer
Euro handle Pro handle Euro handle Pro handle
A9³⁄₄"9³⁄₄"9⁷⁄₈"9⁷⁄₈"
B 30" 30" 30" 30"
Handle
Mounting
Studs
Refrigerator
Compartment
Handle
Custom Refrigerator
Compartment Panel
Setscrews
#10-24 x 1" Screws
A
B
W10194026A
Vue de la page 0
1 2 3 4

Résumé du contenu

Page 1 - HANDLE ACCESSORY

INSTRUCTION SHEET FOR BUILT-IN REFRIGERATORHANDLE ACCESSORYBEFORE YOU BEGIN: The handle and handle mounting hardware must be installed before installi

Page 2 - Install the freezer handle

2Install the freezer handleIMPORTANT: See Figure 2 and the Freezer Door table for handle mounting hole requirements as well as handle mounting hole lo

Page 3 - POIGNÉE ACCESSOIRE

3FICHE D'INSTRUCTIONS POUR RÉFRIGÉRATEUR ENCASTRÉPOIGNÉE ACCESSOIREAVANT DE COMMENCER : La poignée et les pièces de montage de la poignée doivent

Page 4

Installation de la poignée du congélateurIMPORTANT : Voir la figure 2 et le tableau (Porte du congélateur) pour les spécifications de trous de montage

Commentaires sur ces manuels

Pas de commentaire